created: 2021/05 mod:2021/09

Unterschiede

Hier werden die Unterschiede zwischen zwei Versionen angezeigt.

--- modellbau:planes:x4inch [2021/05/27] – hermenj
+++ modellbau:planes:x4inch [2021/09/28] (aktuell) – [Settings:] hermenj
@@ Zeile 11: / Zeile 11: @@
     * Motors: 4x [[bg>Brotherhobby-Tornado-T1-1407-3600KV-4S-Racing-Edition-Brushless-Motor-for-FPV-Racer-p-1097174.html|Brotherhobby Tornado T1 1407 3600KV]] with [[bg>10-Pairs-Kingkong-4045-4x4_5-Inch-PC-Fiberglass-Propellers-CW-CCW-p-1029149.html|Kingkong 4045]] Props.
     * ESCs: <del>[[bg>20x20mm-XJB-F425-Dshot-Flytower-Micro-F4-AIO-OSD-BEC-Flight-Control-25A-Blheli_S-2-4S-4-In-1-ESC-p-1148284.html|20x20mm-XJB-F425-Dshot-Flytower]] AIO with 20/25A ESCs and OSD.</del>
-    * RX: [[bg>FrSky-XSR-2_4GHz-16CH-ACCST-Receiver-S-Bus-CPPM-Output-Support-X9D-X9E-X9DP-X12S-X-Series-p-1031481.html|FrSky XSR]]
+    * RX: <del>[[bg>FrSky-XSR-2_4GHz-16CH-ACCST-Receiver-S-Bus-CPPM-Output-Support-X9D-X9E-X9DP-X12S-X-Series-p-1031481.html|FrSky XSR]]</del> Upgraded to [[bg>https://www.banggood.com/0_42g-Happymodel-2_4G-ExpressLRS-EP1-Nano-High-Refresh-Rate-Ultra-small-Long-Range-RC-Receiver-for-RC-Drone-p-1835181.html|Happymodel EP1 eLRS Receiver]]
     * Battery: [[https://hobbyking.com/de_de/turnigy-bolt-850mah-4s-15-2v-65-130c-high-voltage-lipoly-pack-lihv.html|Turnigy Bolt 850mAh 4S]]
     * Thrust: 4x 700g !!!
@@ Zeile 19: / Zeile 19: @@
 </columns>
-Dismantled the defect [[modellbau:planes:x115|X115]] and [[modellbau:planes:afro170|Afro170]] to harvest some parts.
+Dismantled the defect [[modellbau:planes:x115|]] and [[modellbau:planes:afro170|]] to harvest some parts.
-Wanted to have a small simple frame with a simple exchangeable fpv canopy this time - AUW under 250g. This version is the 4" Frame made out of one carbon fiber Tricopter arm from RCExplorer. There is although its smaller sister, the [[modellbau:planes:x3inch|x3inch]].
+Wanted to have a small simple frame with a simple exchangeable fpv canopy this time - AUW under 250g. This version is the 4" Frame made out of one carbon fiber Tricopter arm from RCExplorer. There is although its smaller sister, the [[modellbau:planes:x3inch|]].
 The Prototype was flying pretty good, but ended up somewhere far - i guess in a tree. RSSI Search did not really help this time and had to watch the voltage go down on the telemetry screen until the signal was lost.
 After that was was lost in the forest, i started building a new one with the better Brotherhobby motors and a small 20x20 AIO Board.
+Many many Flights and many many Crashed later this thing was still my favorite quad, indestructible and powerful  -  until it took a small bath in the pond ;-)
+Well, time for an upgraded AIO FC and some digital FPV.
 ===== Pics: =====
 {{gallery>modellbau:planes:x4inch?direct}}
 ===== Links: =====
@@ Zeile 36: / Zeile 38: @@
 ===== Settings: =====
-  * PBF3-EVO uses Betaflight PIKO Target.
+Use [[https://github.com/mbilozub/fpv_custom_mods/tree/master/mods/dji-warning/betaflight|Custom Betaflight]] for BF warnings on DJI OSD
-  * For DSHOT: Re-map motor 1 to the PPM pin, To allow the use of the LED pin Re-map motor 4 to motor 5 signal out a01 <code>
+<code>
-resource ppm none
+#
-resource motor 1 A07
-resource motor 4 A01
+# diff all
+# version
+# Betaflight / STM32F405 (S405) 4.2.0 Jul 13 2020 / 14:28:11 (a7ec0aa) MSP API: 1.43
+# config: manufacturer_id: JHEF, board_name: JHEF405, version: dfa09d94, date: 2021-03-06T10:55:26Z
+# start the command batch
+batch start
+# reset configuration to default settings
+defaults nosave
+board_name JHEF405
+manufacturer_id JHEF
+mcu_id 002c003c3548500720313753
+signature
+# name: JOH 4INCH
+# feature
+feature -RX_PARALLEL_PWM
+feature -AIRMODE
+feature GPS
+feature TELEMETRY
+# serial
+serial 0 2 115200 57600 0 115200
+serial 2 1 115200 57600 0 115200
+serial 5 64 115200 57600 0 115200
+# led
+led 0 8,6::CB:8
+led 1 9,6::CB:8
+led 2 10,6::CB:8
+led 3 11,6::CB:8
+# aux
+aux 0 0 0 1700 2100 0 0
+aux 1 1 1 900 1300 0 0
+aux 2 2 1 1300 1700 0 0
+aux 3 46 2 1700 2100 0 0
+aux 4 13 3 1700 2100 0 0
+aux 5 28 1 1300 2100 0 0
+# master
+set acc_calibration = 9,11,-44,1
+set mag_hardware = NONE
+set baro_hardware = NONE
+set rssi_channel = 16
+set serialrx_provider = CRSF
+set motor_pwm_protocol = DSHOT600
+set failsafe_procedure = GPS-RESCUE
+set ibata_scale = 295
+set small_angle = 63
+set gps_provider = UBLOX
+set gps_auto_baud = ON
+set gps_rescue_initial_alt = 40
+set gps_rescue_descent_dist = 100
+set gps_rescue_throttle_hover = 1270
+set gps_rescue_min_sats = 6
+set gps_rescue_allow_arming_without_fix = ON
+set report_cell_voltage = ON
+set osd_warn_dji = ON
+set osd_vbat_pos = 14675
+set osd_rssi_pos = 2197
+set osd_flymode_pos = 2151
+set osd_crosshairs_pos = 14574
+set osd_current_pos = 2342
+set osd_mah_drawn_pos = 2407
+set osd_craft_name_pos = 2255
+set osd_display_name_pos = 117
+set osd_gps_speed_pos = 2183
+set osd_gps_lon_pos = 2444
+set osd_gps_lat_pos = 2440
+set osd_gps_sats_pos = 2228
+set osd_home_dir_pos = 2383
+set osd_home_dist_pos = 2414
+set osd_altitude_pos = 2214
+set osd_power_pos = 2375
+set osd_warnings_pos = 14793
+set osd_avg_cell_voltage_pos = 2355
+set gyro_1_align_yaw = 900
+set name = JOH 4INCH
+profile 0
+# profile 0
+set p_pitch = 37
+set i_pitch = 81
+set d_pitch = 28
+set f_pitch = 86
+set p_roll = 34
+set i_roll = 77
+set d_roll = 25
+set f_roll = 81
+set p_yaw = 37
+set i_yaw = 81
+set f_yaw = 81
+set d_min_roll = 17
+set d_min_pitch = 18
+profile 1
+profile 2
+# restore original profile selection
+profile 0
+rateprofile 0
+rateprofile 1
+rateprofile 2
+rateprofile 3
+rateprofile 4
+rateprofile 5
+# restore original rateprofile selection
+rateprofile 0
+# save configuration
 save
+#
 </code>
-see: https://github.com/betaflight/betaflight/wiki/DSHOT%20ESC%20Protocol

Ich garantiere bei meinen Bauberichten und Teilelisten keine Vollständigkeit etc...es wird aus den Teilen gebastelt die gerade herumliegen.
Bitte keine Anfragen zum Bau/Fräsen von Frames, Teilen oder sonstigen Aufträgen. Ich betreibe die Seite rein als Hobby und nutze die zur Verfügung stehende Zeit gerne für meine eigenen Projekte.
Bei einigen Projekten werde ich zu gegebener Zeit die Pläne veröffentlichen - aber auch hier lasse ich mich ungern hetzten ;-)

No waranties for completeness of any contructions, part lists etc.. I build from party i have just lying around in my workshop.
Please, No requests to buy frames, builds, etc.. I run this page in my spare-time and as hobby only. Want to keep my free time to work on my own projects - sorry
I will release the plans for some build at some point in time, but again, please don't ask for unreleased plans, i don't want to get rushed ;-)

der-frickler.net

Benutzer-Werkzeuge

Webseiten-Werkzeuge

Unterschiede

Seiten-Werkzeuge