der-frickler.net

Benutzer-Werkzeuge

Webseiten-Werkzeuge

Sie befinden sich hier: der-Frickler.net » Technik » Milly - the small CNC
technik:millycnc
created: 2019/09 mod:2020/11

Unterschiede

Hier werden die Unterschiede zwischen zwei Versionen angezeigt.

Link zu dieser Vergleichsansicht

Beide Seiten der vorigen RevisionVorhergehende Überarbeitung
Nächste Überarbeitung		Vorhergehende Überarbeitung
technik:millycnc [2019/09/28] – hermenjtechnik:millycnc [2020/11/08] (aktuell) – hermenj
Zeile 1: Zeile 1:
 ====== Milly - the small CNC ====== ====== Milly - the small CNC ======
  
-{{:technik:millycnc:milly_cnc_009.jpg?direct&600 |}} **Well there were at least two reasons that lead to this project. I was playing with different kind of GRBL controllers based on STMF1 Blue Pill and ESP32 and i wanted some hardware to easily test them. On the other hand i was cleaning up the workshop in the basement from former CNC projects and found some leftover linear guides, trapezoidal spindles, NEMA 17 and 23 Steppers etc... **+{{:technik:millycnc:milly_cnc_034.jpg?direct&600 |}} **Well there were at least two reasons that lead to this project. I was playing with different kind of GRBL controllers based on STMF1 Blue Pill and ESP32 and i wanted some hardware to easily test them. On the other hand i was cleaning up the workshop in the basement from former CNC projects and found some leftover linear guides, trapezoidal spindles, NEMA 17 and 23 Steppers etc... **
  
  
-After drawing down some ideas i ordered some aluminum extrusion s matching the 300 and 250mm rails i had laying around. With the pfofiles odered to the matching length i finalized the drawing of the small Milly CNC with a footprint a bit bigger than an A4 paper.+After drawing down some ideas i ordered some aluminum extrusions matching the 300 and 250mm rails i had laying around. With the profiles ordered to the matching length i finalized the drawing of the small Milly CNC with a footprint a bit bigger than an A4 paper.
  
 The Plan is to fit all needed electronics into the base of the CNC. This means the power supply for motors and spindle as well as the full CNC controller. I guess it will the the GRBL ESP32 with SD-card and Webinterface/Wifi, which makes this machine completely self contained. The Plan is to fit all needed electronics into the base of the CNC. This means the power supply for motors and spindle as well as the full CNC controller. I guess it will the the GRBL ESP32 with SD-card and Webinterface/Wifi, which makes this machine completely self contained.
  
 +Front and back, flanges and some other parts were milled out of 8mm HPL. The Working plate is build out of 2080 and 2060 profiles which hold the MGN15 rails of the X-Axis. After trying to build the portal with 6040 extrusion and 8x8 trapezoidal rods, i changed that to 4080U extrusion which has enough space to run an SFU1204 Ballscrew inside the profile and still have enough room to fit the MGN12 rails of the Y-Axis.
 +
 +All Electronics were mounted on the back side. 36V 7A PSU on the left and a printed mountplate with ESP32 + grbl Shield, 5V regulator and a FET to control the spindle on the right side. On the front there is the main power switch on the left, GRBL buttons for reset, hold, start on the left.
 ===== Hardware parts ===== ===== Hardware parts =====
  
Zeile 33: Zeile 36:
    
 **Ballscrew spindles** **Ballscrew spindles**
-  * [[https://www.aliexpress.com/item/33062454998.html|SFU1204 350mm]] +  * [[https://www.aliexpress.com/item/33062454998.html|SFU1204 350mm]] $13 
-  * [[bg>SFU1204-Ball-Screw-With-Single-Ballnut-Length-300mm-For-CNC-Parts-p-1120139.html|SFU1204 300mm]]+  * [[bg>SFU1204-Ball-Screw-With-Single-Ballnut-Length-300mm-For-CNC-Parts-p-1120139.html|SFU1204 300mm]] $13
   * [[bg>5mm-x-10mm-Aluminum-Flexible-Shaft-Coupling-OD19mm-x-L25mm-CNC-Stepper-Motor-Coupler-Connector-p-994362.html|Shaft Coupler 5mm 10mm]] 2x $2   * [[bg>5mm-x-10mm-Aluminum-Flexible-Shaft-Coupling-OD19mm-x-L25mm-CNC-Stepper-Motor-Coupler-Connector-p-994362.html|Shaft Coupler 5mm 10mm]] 2x $2
   * [[bg>810121517mm-Bore-Diameter-Zinc-Alloy-Pillow-Block-Flange-Bearing-KFL-Series-p-1119328.html|KFL08 bearing block 8mm]] 2x $1.5   * [[bg>810121517mm-Bore-Diameter-Zinc-Alloy-Pillow-Block-Flange-Bearing-KFL-Series-p-1119328.html|KFL08 bearing block 8mm]] 2x $1.5
Zeile 53: Zeile 56:
  
 {{gallery>technik:millycnc?direct}} {{gallery>technik:millycnc?direct}}
 +
 +
 +===== Videos =====
 +
 +test-running both axis with TR8x8 spindles
 +{{youtube>d8GeqPW9bAw}}
  
  

Ich garantiere bei meinen Bauberichten und Teilelisten keine Vollständigkeit etc...es wird aus den Teilen gebastelt die gerade herumliegen.
Bitte keine Anfragen zum Bau/Fräsen von Frames, Teilen oder sonstigen Aufträgen. Ich betreibe die Seite rein als Hobby und nutze die zur Verfügung stehende Zeit gerne für meine eigenen Projekte.
Bei einigen Projekten werde ich zu gegebener Zeit die Pläne veröffentlichen - aber auch hier lasse ich mich ungern hetzten ;-)

No waranties for completeness of any contructions, part lists etc.. I build from party i have just lying around in my workshop.
Please, No requests to buy frames, builds, etc.. I run this page in my spare-time and as hobby only. Want to keep my free time to work on my own projects - sorry
I will release the plans for some build at some point in time, but again, please don't ask for unreleased plans, i don't want to get rushed ;-)

technik/millycnc.1569665496.txt.gz · Zuletzt geändert: 2019/09/28 von hermenj

Seiten-Werkzeuge

Falls nicht anders bezeichnet, ist der Inhalt dieses Wikis unter der folgenden Lizenz veröffentlicht: CC Attribution-Noncommercial-Share Alike 4.0 International
CC Attribution-Noncommercial-Share Alike 4.0 International Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki